Tuesday, December 13, 2011

Cool Whip

It finally somewhat worked. The structure of the cool whip was very contingent which means that it stayed together and was very hard to force apart. in the end, the bowl hitting the cool whip was instrumental in it actually working. This assignment was very challenging and tolling on my mind. Luckily, we were able to get the bag in place and have it stay still without disrupting the integrity of the entire structure. The bag of cool whip would get in the way of the ultrasonic sensor, so we decided to go with a clap sensor. we probably should have set it for a higher level due to Zander's incredibly loud voice. All and all it was a good ending to a very tough project.

Chris Solar

Railway track completion

We have finalized our design and tested then retested over and over. We have increased the speed of which the platform travels and adjusted the time to stop it at the desired locations.

Minor Change in Sprinklebot

The robot did not wait 45 seconds after it sprinkled like we had programmed it to. If we didn't change it then the robot would shake the sprinkles out when the robot carrying the bowl came back. We figured out that the problem was in the programming. We had the 45 second wait set up for a time sensor, which we didn't have. So, we changed the 45 second wait to the control time section. The robot now waits 45 seconds to shake the sprinkles out after it has done it before.

Syrup Completion

Last class our group made some changes to the design of out syrup dispenser. We added plates so the two bricks could balance on top of the dispenser. After we did that we made some changes to the programing to make the dispenser push down six times instead of three time. We have now completed the syrup dispenser

Friday, December 9, 2011

Dec 9

today we put together the assembly line for the ice cream. AFter many attempts we had to change the timer and the sensor distance for our oreo robot. We found out the correct time for the robot to react and works 100%. We also decided to have two shakes of the oreos instead of one....DOUBLE THE OREOS!!!

Syrup changes

We discovered that the dispenser would require an extra amount of force to be depressed. It was decided that we would have to use 2 bricks to depress the dispenser. We used a large amount of plates in order to balance the two bricks. The bricks would then be pulled down by a sort of pulley system. This process turned out to be the most efficient way to get syrup.

Change in sprinkles group

We are changing the program so that the ice cream cart has time to travel back to its starting point. We are setting a delay on the ultrasonic sonic sensor for ten seconds so that when the ice cream carrier moves backwards, the sprinkles machine wont initiate and the sprinkles wont be wasted.

Wednesday, December 7, 2011

It works!

Today we got the rail to successfully pull the cup down and back, and we decided to tape down the rail for support. All we have left is to incorporate the touch sensor and we can start testing.

Sprinkles group

The sprinkles group is continuing to help others groups, mainly the chocolate syrup group. We are offering ideas and solutions to their dilemma.
Today we primarily finished polishing up the design. We added a textbook along with the wooden block to counter the motor's force. Michael posted some of our progress on the wiki, and mac and I finally stabilized the robot with the textbook. Michael and I went to some other groups to see how their designs were going.

Monday, December 5, 2011

New Design #2

Today we finished building the new design for our syrup dispenser but we do not have the drawing, yet. We were able to start testing today and have solved most of the errors in the program. We are still troubleshooting with some of the problems involving dispensing the chocolate more than once per bowl. We hope to fix it by adding a stable platform on which to balance the weights.

Todays activitys

Mac
today all we did was edit the wiki and post to the blog along with running through the program again to make sure that we didnt have any problems with the robot or anything. it was a good day and we got a lot done.

Finished

We are done and we are helping other groups.

Friday, December 2, 2011

New Design for Syrup

Our old design that involved a gear box and pressing down on the nozzle had major flaws, and we were not able to successfully dispense the syrup. We have now moved onto a design were two motors with a string attached between them pulls the brick itself to press down on the nozzle. We will test next block.

Final Changes for Sprinkles Group

The only change we had to make in our robot today was to make the ultrasonic sensor higher. We raised the ultrasonic sensor about two inches, making it able to detect the bowl.