Tuesday, December 13, 2011

Cool Whip

It finally somewhat worked. The structure of the cool whip was very contingent which means that it stayed together and was very hard to force apart. in the end, the bowl hitting the cool whip was instrumental in it actually working. This assignment was very challenging and tolling on my mind. Luckily, we were able to get the bag in place and have it stay still without disrupting the integrity of the entire structure. The bag of cool whip would get in the way of the ultrasonic sensor, so we decided to go with a clap sensor. we probably should have set it for a higher level due to Zander's incredibly loud voice. All and all it was a good ending to a very tough project.

Chris Solar

Railway track completion

We have finalized our design and tested then retested over and over. We have increased the speed of which the platform travels and adjusted the time to stop it at the desired locations.

Minor Change in Sprinklebot

The robot did not wait 45 seconds after it sprinkled like we had programmed it to. If we didn't change it then the robot would shake the sprinkles out when the robot carrying the bowl came back. We figured out that the problem was in the programming. We had the 45 second wait set up for a time sensor, which we didn't have. So, we changed the 45 second wait to the control time section. The robot now waits 45 seconds to shake the sprinkles out after it has done it before.

Syrup Completion

Last class our group made some changes to the design of out syrup dispenser. We added plates so the two bricks could balance on top of the dispenser. After we did that we made some changes to the programing to make the dispenser push down six times instead of three time. We have now completed the syrup dispenser

Friday, December 9, 2011

Dec 9

today we put together the assembly line for the ice cream. AFter many attempts we had to change the timer and the sensor distance for our oreo robot. We found out the correct time for the robot to react and works 100%. We also decided to have two shakes of the oreos instead of one....DOUBLE THE OREOS!!!

Syrup changes

We discovered that the dispenser would require an extra amount of force to be depressed. It was decided that we would have to use 2 bricks to depress the dispenser. We used a large amount of plates in order to balance the two bricks. The bricks would then be pulled down by a sort of pulley system. This process turned out to be the most efficient way to get syrup.

Change in sprinkles group

We are changing the program so that the ice cream cart has time to travel back to its starting point. We are setting a delay on the ultrasonic sonic sensor for ten seconds so that when the ice cream carrier moves backwards, the sprinkles machine wont initiate and the sprinkles wont be wasted.

Wednesday, December 7, 2011

It works!

Today we got the rail to successfully pull the cup down and back, and we decided to tape down the rail for support. All we have left is to incorporate the touch sensor and we can start testing.

Sprinkles group

The sprinkles group is continuing to help others groups, mainly the chocolate syrup group. We are offering ideas and solutions to their dilemma.
Today we primarily finished polishing up the design. We added a textbook along with the wooden block to counter the motor's force. Michael posted some of our progress on the wiki, and mac and I finally stabilized the robot with the textbook. Michael and I went to some other groups to see how their designs were going.

Monday, December 5, 2011

New Design #2

Today we finished building the new design for our syrup dispenser but we do not have the drawing, yet. We were able to start testing today and have solved most of the errors in the program. We are still troubleshooting with some of the problems involving dispensing the chocolate more than once per bowl. We hope to fix it by adding a stable platform on which to balance the weights.

Todays activitys

Mac
today all we did was edit the wiki and post to the blog along with running through the program again to make sure that we didnt have any problems with the robot or anything. it was a good day and we got a lot done.

Finished

We are done and we are helping other groups.

Friday, December 2, 2011

New Design for Syrup

Our old design that involved a gear box and pressing down on the nozzle had major flaws, and we were not able to successfully dispense the syrup. We have now moved onto a design were two motors with a string attached between them pulls the brick itself to press down on the nozzle. We will test next block.

Final Changes for Sprinkles Group

The only change we had to make in our robot today was to make the ultrasonic sensor higher. We raised the ultrasonic sensor about two inches, making it able to detect the bowl.

Wednesday, November 30, 2011

New design for Whipped Cream

We have found major flaws in our plan and we are working on making legs to stabilize the robot. We have also found another place to put the motor since the original placement of motor wasn't functioning as planned. So the group is making new plans to dispense the cream using a string to pull the nozzle. We are also looking into a new or better way to hold the whipped cream in place.

Rail Way and Car Phase 3

Today we had to rebuild the rail itself because somebody broke it while we were out of class. We decided that it would be far easier to make the entire rail black, since we only had black duct tape to hold it together. We decided that we would inverse the light sensor and have the car stop when we reached a light spot in the track. This would solve a lot of future issue with the light sensor on the bare wood itself. We still need to figure out a way to anchor the pulley on the end of the track.

New Design


This is the new design described in the wiki. We added a counterweight and an ultrasonic sensor.

Oreo group currently

today we have made the program for the oreo robot to work on the conveyor belt. we have had to modify the robot build a bit but all in all it is all turning out well. we are debating on whether to leave the lid on or to take off the lid to get more oreos in the bowl.

Syrup Group- Continued Construction

Once the bottle arrived, we realized that the current design we had would be faulty. We descontructed the old container and started from the beginning. We made a stronger, more stable holder. We also constructed a lever with more torque and power. We are hoping to have the lever push down the top of the bottle.
Rail and Car design:
-we got the rail set up and the motors running
-the car was pulled in both directions without difficulty
-we need to program it to stop in 4 intervals so that it can successfully get its items for the sundae deposited into it.

Monday, November 28, 2011

Finished with Contruction

Today we made some major changes to our design making it taller so that it would go in the bowl with out tipping it over. This allows us to gain more control. We also put an ultrasonic sensor on it so when the bow gets near it knocks the sprinkles in.Our design has a counterweight on it now so it will not fall over from the knocking motion.

Syrup Group

On the third day we refined the dispenser model, and added the counter-balances so as to test it. We also wrote the program for the robot, which will hit the dispenser and dispense the chocolate syrup onto the ice cream bowl. We were not able to continue testing as we did not have the actual container and dispenser for the chocolate syrup. We plan to test extensively during the next class period.

Problems with Whipped Cream

Today we are having problems trying to put counter weight and also finding a place to put the arm that will hit the whipped cream can. When we finally found a place to put the motor, we came across the problem of the whipped cream not dispensing it's creamy filling.

Whipped Cream Group

Our group finished drawing the designs to our device and we have started working on the foundation of our robot. Chris is thinking of another design that will release the whipped cream, but sadly it makes more problems than solving. So we still plan to stick to the original plan, which consists of an arm holding the can upside down and a motor on its side rotating an arm that will slowly tap the tip of the whipped cream.

Syrup

On the second day of our project we have finished the designs and ideas for our syrup dispenser. (shown above) We have made our first model of the dispenser but can not fully test it due to our lack of materials. Yet we have been adjusting the program without the dispenser.

Monday, November 21, 2011

today we built the arm that will push down on the dispenser,and the stand that the dispenser will be held in. we also finished the programing of the arm to make it push down on the dispenser.

Sprinkles Group

On the second day of our project we started construction on our sprinkle dispenser. We are moving along quite swelly and have our design down pretty good. We should be done by next class.
Here is Our design-

Oreo group

This is our design for the Oreo pieces dispenser. It has a stabilizing counterweight on the back. The container is secured to the motor which slings it forward and stops for a few seconds then pulls back up.

Railway track

Today, we installed a light sensor to the platform so that it will detect the dark strips on the rail, which is a 2x1 piece of wood, and stop. That was the last step to the build; after that, we tested to see how well the platform would run along the rail. We will also equip the strings on each end of the platform, which are attached to a motor then we will perform test runs.

Thursday, November 17, 2011

First Day

On the first day of our sundae robot design project, we began in a meeting type setting and discussed the different elements required for our project to succeed. We broke the task into 5 different areas: track production, sprinkle distribution, syrup dispenser, whipped cream dispenser, and crushed oreos dispenser. The type of track we are using is a pulley type system on a train track. The platform will be pulled by strings and be sturdy on a track.

Friday, November 11, 2011

First Post

This blog will be used to post updates for the Unit 2 Test where students will create a robotic assembly line for creating a sundae, also known as RoboSundae.