Wednesday, November 30, 2011

New design for Whipped Cream

We have found major flaws in our plan and we are working on making legs to stabilize the robot. We have also found another place to put the motor since the original placement of motor wasn't functioning as planned. So the group is making new plans to dispense the cream using a string to pull the nozzle. We are also looking into a new or better way to hold the whipped cream in place.

Rail Way and Car Phase 3

Today we had to rebuild the rail itself because somebody broke it while we were out of class. We decided that it would be far easier to make the entire rail black, since we only had black duct tape to hold it together. We decided that we would inverse the light sensor and have the car stop when we reached a light spot in the track. This would solve a lot of future issue with the light sensor on the bare wood itself. We still need to figure out a way to anchor the pulley on the end of the track.

New Design


This is the new design described in the wiki. We added a counterweight and an ultrasonic sensor.

Oreo group currently

today we have made the program for the oreo robot to work on the conveyor belt. we have had to modify the robot build a bit but all in all it is all turning out well. we are debating on whether to leave the lid on or to take off the lid to get more oreos in the bowl.

Syrup Group- Continued Construction

Once the bottle arrived, we realized that the current design we had would be faulty. We descontructed the old container and started from the beginning. We made a stronger, more stable holder. We also constructed a lever with more torque and power. We are hoping to have the lever push down the top of the bottle.
Rail and Car design:
-we got the rail set up and the motors running
-the car was pulled in both directions without difficulty
-we need to program it to stop in 4 intervals so that it can successfully get its items for the sundae deposited into it.

Monday, November 28, 2011

Finished with Contruction

Today we made some major changes to our design making it taller so that it would go in the bowl with out tipping it over. This allows us to gain more control. We also put an ultrasonic sensor on it so when the bow gets near it knocks the sprinkles in.Our design has a counterweight on it now so it will not fall over from the knocking motion.

Syrup Group

On the third day we refined the dispenser model, and added the counter-balances so as to test it. We also wrote the program for the robot, which will hit the dispenser and dispense the chocolate syrup onto the ice cream bowl. We were not able to continue testing as we did not have the actual container and dispenser for the chocolate syrup. We plan to test extensively during the next class period.

Problems with Whipped Cream

Today we are having problems trying to put counter weight and also finding a place to put the arm that will hit the whipped cream can. When we finally found a place to put the motor, we came across the problem of the whipped cream not dispensing it's creamy filling.

Whipped Cream Group

Our group finished drawing the designs to our device and we have started working on the foundation of our robot. Chris is thinking of another design that will release the whipped cream, but sadly it makes more problems than solving. So we still plan to stick to the original plan, which consists of an arm holding the can upside down and a motor on its side rotating an arm that will slowly tap the tip of the whipped cream.

Syrup

On the second day of our project we have finished the designs and ideas for our syrup dispenser. (shown above) We have made our first model of the dispenser but can not fully test it due to our lack of materials. Yet we have been adjusting the program without the dispenser.

Monday, November 21, 2011

today we built the arm that will push down on the dispenser,and the stand that the dispenser will be held in. we also finished the programing of the arm to make it push down on the dispenser.

Sprinkles Group

On the second day of our project we started construction on our sprinkle dispenser. We are moving along quite swelly and have our design down pretty good. We should be done by next class.
Here is Our design-

Oreo group

This is our design for the Oreo pieces dispenser. It has a stabilizing counterweight on the back. The container is secured to the motor which slings it forward and stops for a few seconds then pulls back up.

Railway track

Today, we installed a light sensor to the platform so that it will detect the dark strips on the rail, which is a 2x1 piece of wood, and stop. That was the last step to the build; after that, we tested to see how well the platform would run along the rail. We will also equip the strings on each end of the platform, which are attached to a motor then we will perform test runs.

Thursday, November 17, 2011

First Day

On the first day of our sundae robot design project, we began in a meeting type setting and discussed the different elements required for our project to succeed. We broke the task into 5 different areas: track production, sprinkle distribution, syrup dispenser, whipped cream dispenser, and crushed oreos dispenser. The type of track we are using is a pulley type system on a train track. The platform will be pulled by strings and be sturdy on a track.

Friday, November 11, 2011

First Post

This blog will be used to post updates for the Unit 2 Test where students will create a robotic assembly line for creating a sundae, also known as RoboSundae.